Showing results: 121 - 135 of 282 items found.
-
Mornsun Guangzhou Science & Technology
MORNSUN AC/DC enclosed switched-mode power supplies (SMPS) feature complete EMC tests and protections, high efficiency, and wide selection. MORNSUN SMPS withstands 300VAC surge input for 5 seconds. 305RAC (305Vin reliable under all conditions) AC to DC SMPS module is included. 305RAC Series is a collection of AC/DC converters that can run from nominal 85 VAC up to 305 VAC and are safety certified to UL/IEC/EN standards, with CB Reports. These AC to DC enclosed switching power supplies in MORNSUN SMPS Power Supplies portfolio meet IEC/EN61000-4, CISPR32/EN55032, IEC/UL/EN62368, EN60335, and GB4943 standards and are widely used in areas of industrial, LED, street light control, electricity, security, telecommunications, smart home, etc. They comply with the latest global energy efficiency standards. The most high-quality AC to DC SMPS ranging from 15W to 1500W witness the continuous innovation of MORNSUN SMPS power supply family.
-
EL30000 Series -
Keysight Technologies
The Keysight EL30000 Series Bench electronic load with a built-in data logger provides new levels of test insights for your devices like power supplies, batteries, DC to DC converters, and more. View voltage and current trends to make real-time decisions, rather than waiting hours for a test to complete. At the heart of the EL30000 is a highly accurate measurement system that provides real-time updates to the large display. Keysight’s PathWave BenchVue software allows you to operate the electronic load remotely, execute test sequences, log data, and integrate with other test instruments. Single and dual-channel models are available with up to 600 W for measurements that require more power. Start your test with confidence and finish with results you trust.
-
Hilkar
Crowbar resistors are three phase resistance banks which are connected to the rotor windings of the DFIG (Doubly-Feed Induction Generator) such as wind power generator. They are used to prevent damage to the inverter circuits attached to rotor side when a fault occurs in the grid. DFIG power converter, which has a restricted over-current limit, needs special attention during faults in the grid. If the rotor current or DC link voltage reaches the threshold value, crowbar resistors disconnect the converter in order to prevent the generator turning into a squirrel cage induction machine. By crowbar resistors, the DFIG could stay connected to the grid and continue its operation.
-
Model 253 -
Telebyte, Inc.
FEATURES: DB9 Data Port; Compatible with PC/386/486; Full Duplex; Surge Protection. Adding an RS-422 interface to a PC is now a snap. The Model 253 Interface Converter does this for full duplex signals at data rates up to 19.2 KBPS, without requiring any AC or DC power. With only TD, RD and ground, the Model 253 provides operation over 8,000 feet of twisted pair into a load of 120 Ohms.
-
MP-9820 -
Ono Sokki
MP-9820 is a magneto-electric-rotation detector using an internal hall element, a permanent magnet, DC amplifier, and voltage regulator in its compact body. Using MP-9820 in combination with detection gear enables deriving stable rectangular waveform from ultra low speed all the way through high speed. (1 Hz to 100 kHz)MP-9820 finds wide range of applications and rotational measurement objects by using with TM-3100 series tachometer and FV-1500 FV converter.
-
RFM-ADAFF22 -
Sundance Multiprocessor Technology Ltd.
The RFM-ADAFF22 is a two channel Analog to Digital and two channel Digital to Analog mixed converter FMC which complies with VITA 57.1-2010. Each AD channel provides AC coupled single-end analog input and 16-bit single-ended output with 20-105MHz sampling speed based on ADI AD9650. Each DA channel provides 16-bit single-ended input and one DC coupled differential analog output with 1 – 500MHz sampling speed based on Maxim MAX5888A.
-
RFM-ADAFF62 -
Sundance Multiprocessor Technology Ltd.
The RFM-ADAFF62 is a six channel Analog to Digital and two channel Digital to Analog mixed converter FMC which complies with VITA 57.1-2010. Each AD channel provides AC coupled single-end analog input and 16-bit single-ended output with 20-105MHz sampling speed based on ADI AD9650. Each DA channel provides 16-bit single-ended input and one DC coupled differential analog output with 1 – 500MHz sampling speed based on Maxim MAX5888A.
-
BCD250 -
Computer Conversions Corporation
The BCD Series of BCD to Binary Converters will convert 4 digits of scaled BCD angle data with a full scale of 359.9degrees into 12 Bits of binary angle data (MSB=180degrees). These units are entirely digital, require no timing or control signals and do this conversion in less than 500 nano-seconds. Logic levels are TTL/DTL compatable and +5V DC power is required. They are packaged in a 2.6 x 3.1 x .82" H PC board mounting module.
-
Computer Conversions Corporation
The BCD Series of BCD to Binary Converters will convert 4 digits of scaled BCD angle data with a full scale of 359.9degrees into 12 Bits of binary angle data (MSB=180degrees). These units are entirely digital, require no timing or control signals and do this conversion in less than 500 nano-seconds. Logic levels are TTL/DTL compatable and +5V DC power is required. They are packaged in a 2.6 x 3.1 x .82" H PC board mounting module.
-
Analytic Systems
Made from marine-grade aluminium extrusions or heavy-gauge aluminium sheet metal. Powder-coated or anodized, and use stainless fittings throughout Fitted with robust circuit boards using expensive heavy-gauge copper conductors, designed by Analytic Systems' engineers and assembled in our plant.Models are available to step-up, step-down, stabilize or isolate DC power over a range of 12 to 360 volts. No matter which unit you need, these easy-to-install Voltage Converters will give you many years of reliability.
-
Series RKE -
Kepco, Inc.
These lightweight (less than 7 lbs.), compact (less than 160 cubic inches), fully enclosed/shielded power converters deliver either 24, 36 or 48 volts d-c, to run distributed power systems, motors, actuators or heaters. Their universal a-c input (85-265V a-c) is at home with either 115V a-c or 230V a-c, though they produce significantly more output at the higher input voltage, and should be run from 200-240 volt mains wherever possible.
-
Analog Devices Inc.
Analog Devices offers a wide range of RS-232 transceivers to suit many applications. As RS-232 cable networks and the systems to them can be vulnerable to voltage spikes and ground loops, we have developed a number of innovations that protect against these issues and create an isolated RS-232 environment. We accomplish this through our isoPower® integrated dc-to-dc converters, as well as our iCoupler® technology, which enable the power isolation and signal isolation required for system reliability in a noisy environment.
-
3440A -
Ballentine Laboratories, Inc.
The 3440A measures the true rms of low level RF and microwave signals to over 1GHz. High rms accuracy, traceable to NIST, is assured regardless of waveshape. Common calibration errors are eliminated through temperature compensation of the probe detector diodes; double shielding protects the interchangeable probes from rough handling and pickup. Relative gain or loss measurements are simplified by a 0 dB reference adjustment. DC output proportional to the ac input is provided for analog recorders and to allow operation as an ac-dc converter.
-
73SD4 -
North Atlantic Industries
NAI’s 73SD4 is a DSP-based, PC104-compliant Synchro/Resolver Measurement Board with six separate, isolated channels. These channels can incorporate up to six Synchro/Resolver-to-Digital Tracking Converters in a stack-through module. Each channel also produces differential incremental encoder (A & B) outputs (with programmable resolution) and a zero-degree marker pulse. Commutation outputs are available for 4-, 6-, or 8-pole brushless DC motors that eliminate the need for Hall Effect sensors, thereby reducing both processor time and bus traffic.
-
Teledyne Lincoln Microwave
The Gunn diode is the best known and most readily available device in the family of transferred electron devices (TED). They are employed as DC to microwave converters using the negative resistance characteristics of bulk Gallium Arsenide (GaAs) and only require a standard, low impedance, constant voltage power supply, thereby eliminating complex circuitry. Teledyne Lincoln Microwave’s DC1200 series of GaAs Gunn diodes is designed for operation at fixed frequency (determined by the oscillator cavity) within a specified band under CW or pulsed conditions.
